Welcome to the on line store

 

Below are the many products that can be used to enhance your broadcast products.

They are mainly based on adding capabilities to your mobile equipment and focus
on Blackmagic design products.

Please check regularly as the products are constantly being updated.

For more info click HERE

All prices are in US$. Products ship from Australia.
Use the
Click HERE to order  link to email me for purchasing instructions and final pricing.

A tracking number will be provided after payment has been received and processed.
Invoices available on request.


Please contact me if you have a bulk purchase as I can combine shipping.
Also note that due to the current economic climate all orders are built after payment
received. This may take up to 4 days depending on demand.

For video demonstrations of most products below go to my Lefflerpost YouTube channel.
Last updated Jan 2021

 

Products featured – (click on required item to go direct or just scroll down)

-         T-Bar Controller for ATEM (serial control or ethernet control)

-         8 tally/Macro Controller for ATEM

-         4xCCU MASTER Controller (fully optioned)

-         4xCCU Controller (no options)

-         4xCCU Controller options

-         Serial Controller for ATEM

-         PTZ Interface – allows control of PTZ heads

-         Cable for PTZ (IF)  Interface

-         Joystick for PTZ (IF)  Interface

-         PTZ2ATEM Controller – allows control of ATEM PTZ functions

-         ATEM2PTZ Visca Controller

-         ATEM2CCU -  CCU/PTZ/tally embedder

-         ATEM Hyperdeck control to PTZ – HYP2ATEM converts Hyperdeck shuttle and jog commands to Pan and Tilt ATEM commands (coming soon)

-         ATEM Toolkit

-         GVG 100/110/1000 Panel control of Blackmagic ATEM Production Switchers

-         GVG DIY kits for GVG 100/110/1000 Panel to control of Blackmagic ATEM Production Switchers

-         GVG DIY Kit options - Custom made ribbon cable (40 pin IDC to 20 pin IDC to open end)

-         GVG DIY Kit options - Custom made  ribbon cable  (40 pin IDC to 20 pin IDC to DB 37 pin)

-         GVG DIY Kit options - 'Super bright' LEDs used in the panel modifications

-         GVG DIY Kit options - Serial Interface Kit

-         GVG DIY Kit options - Plastic plate kit

-         dataVideo RMC-260 Panel control of Blackmagic ATEM Production Switchers

-         RMC2ATEM options - 4.2" touch screen control panel

-         RMC2ATEM options - Tally interface box

-         RMC2ATEM options - Plastic Mounting Kit

-         Event Logger 1

-         4xCCU Controller for Blackmagic ATEM Production Switchers

-         Optional Touch Screen Display for the 4xCCU Controller

-         Plastic Mounting Kit for Optional Touch Screen

-         Lens Controllers for Fujinon and Canon B4

-         Lens Controllers accessories

-         Tally light from ATEM return

-         Hyperdeck Emulator

-         notes

 

 

Products

 

T-Bar Controller for ATEM (serial control or ethernet control)

                    Serial T-Bar Controller on the left and ethernet T-Bar Controller on the right

 

Both the T-Bar Serial Controller and the T-Bar Ethernet Controller are designed to work alongside an Elgato Stream Deck
to provide analog functionality, as the Stream Deck is purely a button only device.

The main difference between the T-Bar Serial Controller and the T-Bar Ethernet Controller is the T-Bar Serial Controller
communicates with the ATEM using the RS422 serial port available on some ATEM Production Switchers and the T-Bar Ethernet
Controller
communicates to the ATEM using the ethernet port available on ALL ATEM Production Switchers.

The T-Bar Ethernet Controller is ideal for use with the ATEM Mini as the Mini has a rather complete built in control panel but no functional T-Bar.

 

The T-Bar Ethernet Controller has only the connector for the optional LCD display.

 

 

The T-Bar Serial Controller has a connector for the optional LCD display and an RS422 port to communicate with the ATEM’s serial port using the REMOTE port set to “External control set to GVG100.

 

 
 

 

 

 

 

The main advantage of the T-Bar Serial Controller is that it does not use any of the limited number of ethernet ports on the ATEM.
Also, it is not affected by slow ethernet activity.

 

The rear of the T-Bar Serial Controller has a power IN connector and a USB connector for running configurations and performing software updates.
Both connectors can be used for powering the device.

 

The rear of the T-Bar ethernet Controller has a
power IN connector, a USB connector for running
configurations and performing software updates
and an ethernet connector for interfacing to an
existing network where the ATEM in connected..
All connectors can be used for powering the device
including optional POE.

 

 

Both the T-Bar Serial Controller and the T-Bar Ethernet Controller have a T-bar slider including a CUT button and an AUTO button.
The CUT and AUTO buttons are provided to free up these functions when used in conjunction with a STREAM DECK.

 

The T-Bar Ethernet Controller also has the ability to re-map the CUT and AUTO buttons to perform any of the 100 Macro functions
available on the ATEM.

As the T-Bar Ethernet Controller has a built in ethernet module this can also come with an optional POE (power over ethernet)
allowing operation with just a single cable.

There are 4 LEDs that are user controllable for both HI level and LO level indicators.
The T-Bar has a LED at either end that vary in brightness depending on the position of the T-Bar.

 

Pricing:         

SERIAL T-Bar Controller - $265
ETHERNET T-Bar Controller - $295

ADD options (for Ethernet T-Bar controller) -
Power Over Ethernet +$70 (POE)

Shipping: $35

Availability: NOW (limited stock)

Click HERE to order or quote.

 

HOME

8 Tally/Macro Controller for ATEM

 

The above are some of the variations of the product range:
Top left – 8 TTL Tally with 16 Macro controls
Top right - 8 TTL Tally with 4 Macro controls and POE
Bottom left – 8 TTL Tally, 4 Relay tally and POE
Bottom right - 8 TTL Tally, 8 Relay tally with 4 Macro controls and POE

Many other variations are available.

The x8tally has 8 tally pins that can work as Program tally, Preview tally and Aux buss tally in any combination.
Each tally pin is fully configurable to indicate ANY input source on any program, preview or aux buss.
The very BASIC UNIT has 2 way power (usb (5v) or 'cylindrical connector' (6v - 14v), an ethernet connector,
a 9 pin 'D' for tally TTL connection (inversable) and a 6 pin Minidin for optional Display controller. This also allows access
to controlling ATEM Macros.
Adding the optional Macro buttons gives you hardware control of any preprogrammed ATEM Macro.
The x4 button option allows 4 user selectable macros and the x9 button allows 16 user selectable macros.

NEW for 2022
New software now allows for any or all 8 tally connections to be used as ATEM PROGRAM or PREVIEW buss selectors.
What this means is that you can interface a 3rd party controller with either switch to ground or closing contacts to select sources on either the program or preview rows.

Pricing:         

Basic tally only (power via USB or 12v, 9 pin tally out, 6 pin display connector) - $295

ADD options -
Power Over Ethernet +$70 (POE)
4 x Relay unit +$45 (built in LED and changeover contacts)
8 x Relay unit +$90 (built in LED and changeover contacts)
4 x button Macro control +$45 (to control 4 Macros)
9 x button Macro control +$90 (to control 16 Macros)
Display Unit +$135 (backlit 16x2 character display with 4 buttons)
XLR Tally Box +150 (to use XLR audio cable to run tally to cameras)
ITC-100 interface +75 (to connect directly to the datavideo ITC-100)
Tally Unit to ITC-100 interface or XLR Tally Box cable +$25 (pin to pin DB 9 cable)


Optional Display Unit
This also provides configuration, Status and Macro control

 

 

Optional XLR Tally box
This sends Program and Preview tallies down a standard Audio cable and comes
with 4 x Program/Preview RED/GREEN LEDs built into XLR connectors. These can
then attach to the camera using tape, Velcro etc.

 

 

Optional ITC-100 interface
The ITC-100 interface plugs directly into the rear of the ITC-100 Tally A and tally B connectors.
It is exactly spaced to fit both connectors with the single unit. On the other side there is a
looping 9 pin connector carrying the tally signals from the Basic Tally Unit.
On the top there is a jumper selector to allow Program 1 to 4 tally and Preview 1 to 4 tally
*OR* Program 1 to 8 tally and no Preview tally.
If you require Program 1 to 8 tally AND Preview 1 to 8 tally you will require 2 Basic Tally units.

 

 

 

User Guide –

http://bazcontrollers.com/x8tally/x8tallyUsersGuide.pdf

Youtube video -

https://youtu.be/7taxvOZAPj8  - "ATEM hardware Tally for ATEM Mini and others"
https://youtu.be/PHWFLXYaoiI - Tally and macro Controller for ATEM incl. Mini”
https://youtu.be/cd4wMiPHry8 - "ATEM Mini as a TV station”


Shipping: $35

Availability: NOW

Click HERE to order or quote.

 

HOME

 

 

 

 

4xCCU MASTER Controller (fully optioned)

 

 

The 4xCCU Master Controller is configurable to allow adjustment for 4 of any CCU positions on an
ATEM production switcher and acts as a control surface to mirror the ATEM CCU.

This controller is fully optioned with not just the ATEM CCU and Aux buss control, but also
control for Blackmagic VIDEOHUB, SMARTSCOPE, MULTIVIEW 4 and TERANEX AV/2D/3D!


Each of the 4 CCU positions can be allocated to ANY of the external inputs of any model ATEM.
Each CCU position has dedicated IRIS paddle and PEDESTAL knob + red, green, blue, and lum
paint control knobs for GAIN and GAMMA and red, green and blue paint control knobs for LIFT + an
X/Y JOYSTICK for PTZ pan, TILT, FOCUS and ZOOM. There is also a TOUCHSCREEN for displaying
and controlling extra functions such as GAINdb, SHUTTER, KELVIN, DETAIL, BARS etc

Each IRIS paddle has a push down preview button that is used to select a programmable router input
for previewing on an external Monitor/Waveform/Vectorscope. The controllable router can be either an
ATEM AUX BUSS, a Blackmagic VIDEOHUB or a Blackmagic Multiview 4.


The 4xCCU Master Controller has built in control for an attached BMD SmartScope monitor as well as
full control of the ATEM AUX Busses, BMD Videohub and BMD Multiview  4. This provides control for
any feeds being provided for large screen viewing etc.
Also available is control over Teranex AV/2D/3D units which allow you to do after camera CCU like
control of Gain (iris), PED (black), red, green, blue, and lum gain (paint), R-y, G-y and lots more like
Hue, Saturation and sharpness.

The BMD equivalent with far less features is $4539.

 

Specifications:

* Ethernet connection to any Blackmagic ATEM switcher running v7.5.2 and above
* uses the ATEM built in CCU protocol
* Controls any FOUR cameras that uses the ATEM 'return camera feed'
            - BMD Studio camera
            - BMD Micro Studio camera
            - URSA Broadcast camera
            - URSA Mini Pro 4.6K G2
            - any other BMD camera that boasts CCU controllable
            - all other cameras that have 3rd party ATEM compatible control
              (if the ATEM Software Control Panel can control it, so can this)
* 3 way power. Uses either:
            - POE (power over ethernet)
            - USB power (5v)
            - 2.5mm power (7v to 14v)
* 4 x specialised IRIS/PEDESTAL levers (aka 'paddles')
            - forward/backward controls the IRIS
            - rotary turn controls the pedestal (lift)
            - push down selects each camera in either toggle or latch mode
* adjustable iris range control for either full open to close or partial finer control
* adjustable pedestal for coarse or fine control (default)
* integrated Program, Preview and monitoring TALLY from ATEM or Videohub
* Specialised SmartScope Program/Preview TALLY
* Control of SmartScope display types (Picture, Waveform, Vectorscope, Parade, Audio etc
* Touch screen display for all major operational CCU controls (Gain, Shutter, Kelvin etc)
* Dedicated paint control knobs for Gains, Gammas and Lifts R,G,B,Y
* PTZ joystick PAN, TILT, FOCUS, ZOOM hardware control
* All connections at the rear so multiple units can be mounted side by side
* User selectable camera allocations of ANY ATEM external sources (x4)
* User selectable camera monitor sources (x4):
            - any ATEM AUX buss (when available)
            - any BMD Videohub input
            - any BMD Multiview 4 input
* Individual user selectable toggle/latch camera monitoring (x4)
* User selectable camera monitor router type and output of ANY ATEM sources (x4)
* User selectable SYSTEM, ATEM, VIDEOHUB, SMARTSCOPE and MULTIVIEW 4 IP selections
* User selectable PTZ forward or reverse for both X and Y axis (including LOCK X and LOCK Y)
* Added zoom and focus controls for selected camera types
* full control of ATEM Aux busses source and destinations
* full control of any BMD Videohub source and destinations
* full control of BMD SmartScope (both A and B sides)
* full control of BMD Multiview 4
* ATEM Aux buss or Videohub Control for camera monitoring
* 6 pin I2c expansion connector at rear
* Rear mounted removable MicroSD card (card supplied)
* Software updates via USB port
* Display updates via MicroSD card
* many other features will be shown when the User Manual is complete

Click HERE for User Guide

 

Multiple units

Panel layout

 

Youtube video’s -

https://youtu.be/X32yz2nXWLs - "4xCCUMaster Intro"
https://youtu.be/plR6uydOjuY - "4xCCU Master - CCU Iris control range and position settings"
https://youtu.be/MUge-IQ0H_0 - "Paint control pt 1"
https://youtu.be/5jn5qsaXwPQ - "Paint control pt 2"
https://youtu.be/aFePtr_vpbw - "4xccu controller preview buttons"
https://youtu.be/Zx6QMslG1-o - "ccu controller in factory diagnostics mode"
https://youtu.be/-SO1JWra0bM - "4xccu master controller - scene store pt 1"
https://youtu.be/k5j0EVn8VIA - "4xccu master Videohub Integration"
https://youtu.be/-o4BW-FUOWA - "4xccu master controller - Smart Scope integration"
https://youtu.be/qpQKlFi82gE - "4xccu controller - Multiview 4 integration"

 

 

Price: $1199

Shipping: $35

Availability: Awaiting components

Click HERE to order or quote.

 

HOME

 

4xCCU Controller (no options)

 

This is the same as the 4xCCU MASTER Controller as seen above but without the optional Videohub, Smartscope,
Multiview 4 and Teranex AV/2D/3D interfaces. These can be added later.

The 4xCCU Master Controller is configurable to allow adjustment for 4 of any CCU positions on an ATEM
production switcher and acts as a control surface to mirror the ATEM CCU.

Each of the 4 CCU positions can be allocated to ANY of the external inputs of any model ATEM. Each CCU
position has dedicated IRIS paddle and PEDESTAL knob + red, green, blue, and lum paint control knobs
for GAIN and GAMMA and red, green and blue paint control knobs for LIFT + an X/Y JOYSTICK for PTZ
pan, TILT, FOCUS and ZOOM. There is also a TOUCHSCREEN for displaying and controlling extra functions
such as GAINdb, SHUTTER, KELVIN, DETAIL, BARS etc

Each IRIS PADDLE has a push down preview button that is used to select a programmable router input
for previewing on an external Monitor/Waveform/Vectorscope. The ATEM AUX BUSS can be configured to be
the controllable router.

 

Price: $735   (special promotional price)

Shipping: FREE

Availability: Awaiting components

Click HERE to order or quote.

 

HOME

 

4xCCU Controller options

 

All options will be delivered via email with full instructions and activation codes.

Videohub Control
Click HERE to order.

SmartScope Control
Click HERE to order.

Multiview 4 Control
Click HERE to order.

Teranex Control
Click HERE to order.

ALL Controls
Click HERE to order.

 

HOME

 

Serial Controller for ATEM

 

The Serial Controller for ATEM is not designed to replace an ATEM or other 3rd party control panel, but to allow alternate control in the case of network failure etc.
It can also be used as a low priced MAIN control panel, but with limited functionality due to the simple interface provided by the ATEM and the communications protocol used with the GVG serial interface. There are 4 models varying in price.

 

Basic Controller

Basic+ Controller

Deluxe Controller

Ultra Controller

 

For more information and pricing click HERE to go to web page.

Youtube video’s -

INTRODUCTION TO VARIOUS MODELS

BASIC - operation and setup menus

BASIC+ INTRODUCTION

 

Click HERE to order.

 

HOME

 

 

 

PTZ (IF)  Interface

 

                        

On the left are connectors for power in (7v to 12v), 6pin MiniDIN for local joystick and a USB for 5v power, configuration and firmware updates.
On the right are connectors for pan, tilt, zoom, iris and focus (9p male D), RS422/485 control input (9p female D) and a 6pin MiniDIN for expansion.
On the top is a SHIFT button and a rotary knob for local control and setup functions as indicated by a multicolored LED.

Colorcode chart for various controls of the rotary knob.

 

This is a PTZ (pan, tilt, zoom) with IF (iris, focus) interface for a Bescor MP101 (also compatible with the Vidpro Motorized Pan & Tilt Gimbal Head).
With the addition of IRIS control you can use lower price camera's and match exposures with all the other cameras in your setup.
As LANC commands are added in future releases, they can be included into the PTZ (IF) Interface with free firmware updates.

The PTZ (IF) Interface can be used as a standalone interface in conjunction with a suitable PTZ Controller up to 1.5Km away by using the RS485 connection.
Up to 128 of these PTZ (IF) Interface units can be controlled by a single PTZ Controller by daisy chaining the RS422 connector.
It has selectable protocols including Visca, Pelco-D and Pelco-P. The Visca protocol can work directly with the ATEM Micro Studio Camera’s PTZ connector.
The Pelco-D and Pelco-P interface has automatic baud rate detection.

Compatible with the following…

        

The Bescor PTZ MP101 Motorized Pan/Tilt Head (not supplied with the PTZ (IF) Interface)

 

You can make your own interface cable that connects to the Camera (LANC) and the PTZ (7 pin DIN) or you can purchase one as an optional extra.
You can also purchase a cabled local pan/tilt joystick for setting the camera up on its mount (see PTZ options).
The Bescor takes care of the Pan and Tilt, and included is LANC control to take care of Zoom, Focus and Iris control of the camera; all controlled either via the built in knob OR a connected PTZ controller.

 

            

Some compatible (under $100) PTZ controllers (not supplied with the PTZ (IF) Interface)

 

Click HERE for an introductory video.

Price: $345

Shipping: $35 (local AU$15)

Availability: YES

Click HERE to order.

 

HOME

 

Cable for PTZ (IF)  Interface

 


This cable connects the
PTZ (IF) Interface 9 pin to the Bescor MP101 7 pin DIN control. It also has the LANC connector for connecting to the camera.
This cable is supplied as ribbon to allow for maximum flexibility for when using PTZ heads that can turn 360 degrees.

If you want to save money and build your own here is the wiring diagram….

   

Price: $95

Shipping with PTZ (IF) Interface: $0

Shipping: $35 (local AU$15)

Availability: YES

Click HERE to order.

 

HOME

 

 

Local Joystick for PTZ (IF)  Interface

 

 

This optional XY joystick allows localized pan and tilt control of the PAN and TILT functions. Its main use is for when setting up the camera and testing the pan and tilt limits without having to go back to the main controller which could be far away.

Price: $185 (includes 2 metre 6 pin to 6 pin control cable)

Shipping with PTZ (IF) Interface: $0

Shipping: $35 (local AU$15)

Availability: Awaiting components

Click HERE to order.

 

HOME

 

PTZ2ATEM Controller

   RS422/485 interface connector for PTZ Controller                                              The Ethernet, USB and power connectors

The PTZ2ATEM allows any 3rd party PTZ controller to send PTZ commands via RS485 to control ATEM PTZ functions. Currently, only specialized ATEM control panels provide PTZ functionality, but this unit allows PTZ control for any ATEM.
The ATEM PTZ functions are available either via the RS422 connector on the rear of most ATEM models or as embedded data in the camera return feed on the ATEM program output. This allows all the PTZ commands to coexist alongside the CCU controls and tally indicators for BMD cameras. The controls available are PAN, TILT, ZOOM, FOCUS and IRIS.


Only a single PTZ2ATEM and PTZ controller unit are required to control ALL PTZ cameras.
At the camera end you can use the ATEM2PTZ Controller (shown below) which takes the ATEM camera return and generates Visca as RS422, or a Blackmagic Micro Studio Camera which has built in Visca to RS422.
For the Visca commands you can use the PTZ(IF) Interface (seen above) to control low cost PTZ heads.

You can use any PTZ Controller that supports Pelco protocol on RS485 connectivity (9 pin ‘D’ or screw terminal).

The PTZ2ATEM has no knobs or buttons but has a status tri-coloured LED to indicate ATEM connectivity and Joystick activity.
To adjust settings such as local IP address, the required ATEM IP address, the PTZ protocol,  the controller baud rate, Aux buss control and LED brightness, just connect a USB cable to the built in USB connector and run a terminal program (@115200) on either a Mac or PC. The USB can also be used for power (5v) and firmware updates. There is also an external power connector for 7 to 12 volts.

The PTZ Controller can select any camera available on the ATEM and the subsequent adjustments are then made to that camera.
The PTZ2ATEM also has the ability to control the ATEM’s Aux busses when selecting individual cameras.
There is also available the ability to adjust all controls using 2 separate speed ranges.

This unit is also available as POE (powers from the Ethernet port) when used in conjunction with a suitable router.

 

Price: $285

Shipping: $35 (local AU$25)

Availability: YES

Click HERE to order.

 

HOME

 

ATEM PTZ Visca Controller

 

                             

ATEM2PTZ allows ATEM PTZ commands over camera return to control Visca heads and discrete PTZ heads (Bescor MP101).

This PTZ head controller reads the PTZ data from the ATEM Camera return feed (from coax or fiber) and converts it to either discrete pan and tilt commands and/or RS422 serial commands such as Pelco, Visca etc. It can also provide LANC commands for zoom, iris and focus for compatible cameras.

This unit is similar to the PTZ(IF) Interface as seen above, except this unit derives the PTZ data from the embedded ATEM CCU data, and the PTZ(IF) Interface derives the PTZ data from the BMD Micro Studio Cameras PTZ connector (where the camera does the de-embedding).

The embedded CCU/PTZ data is encoded into the ATEM Program OUT  feed by the ATEM, and the feed is used as the return feed to each camera.
This return feed provides the following;
            - A video program feed for return viewfinder
            - All camera CCU controls as set at the ATEM either by the ATEM software control panel or CCU controller panel
            - Tally light indication for program or preview buss
            - PTZ control for PAN and TILT as set at the ATEM either by a PTZ controller panel or the ATEM hardware control panels

 

Price: $490

Shipping: $35 (local AU$25)

Availability: YES

Click HERE to order.

 

HOME

 

 

ATEM2CCU – CCU/PTZ/tally data embedder

 

This is an ATEM CCU/PTZ/tally controller that converts from an ATEM Ethernet connection to SDI camera return as embedded data.
It works by decoding all the data in the ATEM's CCU ethernet packets (paint, exposure, gain, shutter, PTZ, tally etc) and embeds the data into any HDSDI signal that can be distributed to all your cameras.
This has the added advantage in not needing 4K cabling to get return signals back to the cameras.



As an example, the ATEM2CCU allows the use of the built in 4k down convert SDI output on an ATEM 4K and feeding it into the ATEM2CCU converter SDI INPUT, and then connecting the SDI OUTPUT into the camera return feed of all your cameras. That means your cameras SEND 4K to the ATEM but RECEIVE 3G as return.

The ATEM2CCU can also be used for when you need a different return feed to the cameras such as a multiviewer or a quad split; maybe you need to send off air or a internet feed back to the cameras. But with the ATEM2CCU you can reinsert all the CCU data back into the signal; with zero latency!
That means you will be able to retain all your
camera CCU controls (as set at the ATEM either by the ATEM software control panel or CCU controller panel), Tally light indication for program or preview buss, PTZ control for PAN and TILT (as set at the ATEM either by a PTZ controller panel or the ATEM hardware control panels) as well as your own choice of camera return video pictures.

Using the USB port connected to a computer terminal you can set the Local IP address, the IP address of which ATEM you wish to connect to as well as being able to select what CCU/PTZ/TALLY data you wish to use. The Status LED brightness can also be adjusted. Firmware updates can be applied also using the USB connector.

This unit is also available as POE (powers from the Ethernet port) when used in conjunction with a suitable router.

 

Price: $445

Shipping: $35 (local AU$25)

Availability: YES

Click HERE to order.

 

HOME

 

 

ATEM Toolkit

Dimensions - 162mm x 74mm x 60mm

 
 

 

  

The ATEM Toolkit is a palm sized controller that can connect to the ATEM using just a single ethernet cable. It was initially designed to extend the ATEM Macro capability to a stand alone unit, but in being able to create macro’s, it needed to have access to all the ATEM controls.
It is ideally suited to sit along side an existing ATEM control surface or software control panel, but with the addition of the expansions available, it can also be used as the main controller.
Its main GUI is based on a 3.5” touchscreen with a resolution of 480 x 320. A larger 7” version will be available at the end of 2018 that has a resolution of 800 x 480 (more details to follow).
With 4 fully programable control buttons they can be used as source selections, AUTO, CUT or any other control available. The transition can also be manually controlled using the built in HARDWARE slide fader (T-Bar).

It also has the ability to provide program and preview tallies, as well as expanding the available control to another 23 buttons using the 25 pin expansion connector. There will also be available optional expansion boxes to suit various requirements.
A stand alone optional serial controlled control panel will be available to allow 8 program, 8 preview and 8 function keys along with a T-Bar fader. This serial control will also be compatible with the Datavideo RMC-260 control panel providing basic Program/Preview row selection with associated T-Bar functionality.

The serial control will also be extended to hardware CCU and Audio functions provided by the ATEM.
What makes the
Toolkit even more useful is its ability to expand on existing ATEM functionality with features such as separate key sources for each keyer, timeline control of DVE effects, timeline control of all 4 boxes of SuperSource, etc.

When making adjustments of various ATEM controls they can be achieved using touch screen sliders, buttons, numerical entrys and an assignable infinity controlled rotary knob with button.
The
ATEM Toolkit also has a totally different hardware interface which allows for removable media at the connector end which will be able to be used for uploading media to the ATEM and also used when software updates require display reprogramming.

Toolkit for ATEM - Features:

-   Palm sized

-   Touch Screen multi menu 3.5” display

-   Hardware Transition fader

-   4 user Hardware programable buttons with LEDs

-   Rotary knob with push button for fine adjustment of controls

-   23 additional user programable buttons available using expansion port

-   23 program/preview tallies using expansion port

-   2 Serial (RS232) expansion ports (available on 3.5mm sockets)

·        Future Audio mixer interface

·        Basic Switcher control panel interface

·        RMC-260 control panel interface

·        Future Router interface

-   3 way Power

·        Power over ethernet (POE)

·        USB (5v)

·        2.1mm 9v -12v

-   Controls all ATEM functions (note*)

·        Program and preview row selection

·        ATEM AUX buss control

·        Color Generator setup

·        SuperSource Setup

·        Up Stream Keyer setup (up to 4 keyers on 1 ME ATEM)

·        Down Stream Keyer setup

·        Transitions setup

·        Fade to Black setup

-         Programmable ATEM source to control input selections

-         Control ME 1 or ME 2

-         ATEM Macro record and run

-         ATEM Media Player controller

-         ATEM Audio control panel

-         ATEM CCU control panel

-         Hyperdeck control

 

NOW COMPATIBLE WITH ATEM v7.5.2 AND ABOVE

 

Note* Controls all ATEM functions as at October 2017. Blackmagic Design has added some new functions since and they will be added over time. Current software is work in progress and will welcome any suggestions to improve the product.

Click HERE for more information.

Price: $695

Shipping: $35 (local AU$15)

Availability: Awaiting components

Click HERE to order.

 

HOME

 

 

GVG 100/110/1000 Panel control of Blackmagic ATEM Production Switchers

 

    

 

The GVG 100/110/1000 for the Blackmagic ATEM Production Switchers allows total control
of ANY ATEM.
It features the following ATEM control functions:

- Program/preset row crosspoint control (20 selectable inputs, all independently configurable)

- Key/Aux row crosspoint control (20 selectable inputs, all independently configurable)

- T-Bar manual control of Mix, Wipe, Dip, DVE, Sting

- cut and Auto trans control (including adjustable Auto Trans rate)

- Separate control over 2 x  DSK cut, DSK Auto fade in/out, DSK ON AIR (including adjustable DSK Auto Trans rate)

- Full control over ME 1 or ME 2 transitions including 18 patterns etc, border/softness etc

- Full control over ME 1 or ME 2 keyers LUMA, CHROMA, PATTERN and DVE

- Full control over the Audio mixer settings

- Full control over the CCU settings

- Controls up to 10 CasparCG servers

- many many more features and many more being added

 

NOW COMPATIBLE WITH ATEM v7.5.2 AND ABOVE

 

Complete modified panels -

The panels include

-          installation of the new controller

-         conversion to LED button illumination

-         T-Bar refurbish

-         new connectors on the rear (power, network, USB, expansion

-         panel/button relabeling.

Click HERE for more information.

Price: $1600

Shipping: $195 (local AU$65)

Availability: NO LONGER AVAILABLE

Click HERE to order.

 

HOME

 

DIY kits for GVG 100/110/1000 Panel to control of Blackmagic ATEM Production Switchers